An LPC FMC board which seeks to distribute digital I/O. It is designed to operate at least at 10 MHz, however a better design could allow this board to operate at much higher frequencies. This board is compatible with "PMOD" Connectors.

Software to support the FMC ADC 125M 14B 1CH DAC 600M 14B 1CH mezzanine, including: Linux device driver, HDL firmware, application for data acquisition (ADC) and generating signals (DAC). Included Octave application for card performance measurement (FFT). Uses FMC-bus. More info at the Wiki page

Software to support the FMC ADC 130M 16B 4CH mezzanine, including: configuration application and HDL firmware, with functionality for data acqusition. For use with FCS application. More info at the Wiki page

Software to support the FMC DIO 32CH TTL A mezzanine, including: configuration application and HDL firmware, with functionality for data acqusition. For use with FCS application. More info at the Wiki page

Software to support the FMC ADC 250M 16B 4CH mezzanine, including: configuration application and HDL firmware, with functionality for data acqusition. For use with FCS application. More info at the Wiki page

The spec-box-1n allows to use a SPEC FMC carrier in stand-alone mode, not plugged inside a PC. An external 12 volt supply should be used to power the box. There is no forced ventilation in the box. More info at the Wiki page

The spec-box-3n allows to use up to three SPEC FMC carriers in stand-alone mode, not plugged inside a PC. An internal 230V supply module powers the SPEC boards. The box contains fans to cool the cards. More info at the Wiki page

The FMC bus abstraction implements a Linux kernel bus named fmc. This allows to deal with FMC mezzanines in a carrier-independent way

FMC WorldFIP is an interface card for the WorldFIP network in an LPC FMC form-factor. The hardware is described in the FMC WorldFIP project.

A low cost, low complexity FMC carrier based on Xilinx Artix-7

CROME FMC carrier board (SPEC -based) for the CROME project. More info at the Wiki page

FMC mezzanine board that connects to an Xilinx Virtex-6 FPGA ML605 evaluation board that allows transmitting through 12-channel MPO optical devices a set of 72 links aimed for low-speed (general I/O from the Virtex 6, up to 480 Mbps) and 8 links for high-speed multigigabit transmitters of the Virtex 6 (up to 1600 Mbps). This boards is used for testing other devices. More info at the Wiki page

FmcAdc200k16b11cha is an 11 channel 200kSPS 16 bit ADC card in FMC (FPGA Mezzanine Card) standard. The input voltage range is settable to /-10V or/-5V. The input impedance is 1MOhm.

The Peak Position Detector is a 2 differential channel 10MSPS 16 bit ADC (AD7626) card in FMC (FPGA Mezzanine Card) format. It uses an LPC VITA57 connector. The gain can be set by hardware (default = 41). Two general purpose 50MSPS 16-Bit DAC are implemented and can be programmed as a voltage source. The card also includes 6 input/output LVDS pairs and a 10-bit port digital IO where each single-bit port can be configured individually as input or output. The I/Os that are on micro-HDMI connectors are TTL or LVDS compatible.

The fmc-adc125m14b12ch-dac1250m16b2ch (fmc-dad) board is a 12 ch ADC/ 2 ch DAC channels board using FMC HPC and QSE connectors It has been designed for system requiring a feedback loop mechanism with precise timing, such as the tunning of RF cavities. More info at the Wiki page

The FmcAdc250M12b2cha is a 2 channel 250MSPS 12 bit ADC card in FMC (FPGA Mezzanine Card) format using an LPC connector. The gain can be set by software in three steps: /-50mV,/-0.5V, /-5V. An advanced offset circuit is used in the front-end design of the ADC board, and allows a voltage shift in the range of/- 5V that is independent on the chosen gain range.

The B-Train integrator is a 2 differential channel 2MSPS 18 bit ADC card in FMC (FPGA Mezzanine Card) format. It uses an LPC VITA57 connector. The gain can be set by hardware (default = 1). A gain & offset self-calibrating function is also implemented. This function uses a 1ppm 20-Bit DAC (AD5791) as a reference and can be programmed as a differential voltage source. The card also includes 8 input/output LVDS pairs and a 10-bit port digital IO where each single-bit port can be configured individually as input or output. The I/Os that are on micro-HDMI connectors are TTL or LVDS compatible.

Software to support the FMC ADC 400k 18b 4cha iso mezzanine, including Linux device driver, library and test program.

Fmc-adc-iso-400k18b4cha is a 4 channel 400kSps 18 bit ADC low pin count FPGA Mezzanine Card (VITA 57). The ground reference used for the analog inputs and the ADC is isolated from the ground reference of the FMC connector. Digital Isolators included allow the data transmission between two isolated areas. Voltage Bias between two grounds of up to 1kV can be applied, which is measured with a 100MOhm resistor connected between two grounds and an additional 10 bit ADC. Analog input voltage ranges: /-5V,/-10V. More info at the Wiki page