fd_channel_wb_slave

Fine Delay Channel WB Slave

1. Memory map summary
2. HDL symbol
3. Register description
3.1. Delay Control Register
3.2. Fine Range Register
3.3. Pulse start time / offset (MSB TAI seconds)
3.4. Pulse start time / offset (LSB TAI seconds)
3.5. Pulse start time / offset (8 ns cycles)
3.6. Pulse start time / offset (sub-cycle fine part)
3.7. Pulse end time / offset (MSB TAI seconds)
3.8. Pulse end time / offset (LSB TAI seconds)
3.9. Pulse end time / offset (8 ns cycles)
3.10. Pulse end time / offset (sub-cycle fine part)
3.11. Pulse spacing (TAI seconds)
3.12. Pulse spacing (8 ns cycles)
3.13. Pulse spacing (sub-cycle fine part)
3.14. Repeat Count Register

1. Memory map summary

H/W Address	Type	Name	VHDL/Verilog prefix	C prefix
0x0	REG	Delay Control Register	fd_channel_dcr	DCR
0x1	REG	Fine Range Register	fd_channel_frr	FRR
0x2	REG	Pulse start time / offset (MSB TAI seconds)	fd_channel_u_starth	U_STARTH
0x3	REG	Pulse start time / offset (LSB TAI seconds)	fd_channel_u_startl	U_STARTL
0x4	REG	Pulse start time / offset (8 ns cycles)	fd_channel_c_start	C_START
0x5	REG	Pulse start time / offset (sub-cycle fine part)	fd_channel_f_start	F_START
0x6	REG	Pulse end time / offset (MSB TAI seconds)	fd_channel_u_endh	U_ENDH
0x7	REG	Pulse end time / offset (LSB TAI seconds)	fd_channel_u_endl	U_ENDL
0x8	REG	Pulse end time / offset (8 ns cycles)	fd_channel_c_end	C_END
0x9	REG	Pulse end time / offset (sub-cycle fine part)	fd_channel_f_end	F_END
0xa	REG	Pulse spacing (TAI seconds)	fd_channel_u_delta	U_DELTA
0xb	REG	Pulse spacing (8 ns cycles)	fd_channel_c_delta	C_DELTA
0xc	REG	Pulse spacing (sub-cycle fine part)	fd_channel_f_delta	F_DELTA
0xd	REG	Repeat Count Register	fd_channel_rcr	RCR

2. HDL symbol

→	rst_n_i	Delay Control Register:
→	clk_sys_i	fd_channel_dcr_enable_o	→
⇒	wb_adr_i[3:0]	fd_channel_dcr_mode_o	→
⇒	wb_dat_i[31:0]	fd_channel_dcr_pg_arm_o	→
⇐	wb_dat_o[31:0]	fd_channel_dcr_pg_arm_i	←
→	wb_cyc_i	fd_channel_dcr_pg_arm_load_o	→
⇒	wb_sel_i[3:0]	fd_channel_dcr_pg_trig_i	←
→	wb_stb_i	fd_channel_dcr_update_o	→
→	wb_we_i	fd_channel_dcr_upd_done_i	←
←	wb_ack_o	fd_channel_dcr_force_dly_o	→
←	wb_stall_o	fd_channel_dcr_no_fine_o	→

		Fine Range Register:
		fd_channel_frr_o[9:0]	⇒

		Pulse start time / offset (MSB TAI seconds):
		fd_channel_u_starth_o[7:0]	⇒

		Pulse start time / offset (LSB TAI seconds):
		fd_channel_u_startl_o[31:0]	⇒

		Pulse start time / offset (8 ns cycles):
		fd_channel_c_start_o[27:0]	⇒

		Pulse start time / offset (sub-cycle fine part):
		fd_channel_f_start_o[11:0]	⇒

		Pulse end time / offset (MSB TAI seconds):
		fd_channel_u_endh_o[7:0]	⇒

		Pulse end time / offset (LSB TAI seconds):
		fd_channel_u_endl_o[31:0]	⇒

		Pulse end time / offset (8 ns cycles):
		fd_channel_c_end_o[27:0]	⇒

		Pulse end time / offset (sub-cycle fine part):
		fd_channel_f_end_o[11:0]	⇒

		Pulse spacing (TAI seconds):
		fd_channel_u_delta_o[3:0]	⇒

		Pulse spacing (8 ns cycles):
		fd_channel_c_delta_o[27:0]	⇒

		Pulse spacing (sub-cycle fine part):
		fd_channel_f_delta_o[11:0]	⇒

		Repeat Count Register:
		fd_channel_rcr_rep_cnt_o[15:0]	⇒
		fd_channel_rcr_cont_o	→

3. Register description

3.1. Delay Control Register

HW prefix:	fd_channel_dcr
HW address:	0x0
C prefix:	DCR
C offset:	0x0

31	30	29	28	27	26	25	24
-	-	-	-	-	-	-	-

23	22	21	20	19	18	17	16
-	-	-	-	-	-	-	-

15	14	13	12	11	10	9	8
-	-	-	-	-	-	-	-

7	6	5	4	3	2	1	0
NO_FINE	FORCE_DLY	UPD_DONE	UPDATE	PG_TRIG	PG_ARM	MODE	ENABLE

ENABLE [read/write]: Enable channel
0: channel is disabled
1: channel is enabled
MODE [read/write]: Delay mode select
0: Channel will work as a delay generator, producing delayed copies of pulses comming to the trigger input
1: Channel will work as a programmable pulse generator - producing a pulse which begins at UTC time [U_START, C_START, F_START] and ends at [U_END, C_END, F_END].
Warning: MODE_DLY bit can be safely set only when the TDC and the delay logic are disabled (i.e. when GCR.BYPASS = 1)
PG_ARM [read/write]: Pulse generator arm
write 1: arms the pulse generator.
write 0: no effect.
Note that the time written to [U/C/F]START must be bigger by at least 200 ns than the value of the UTC counter at the moment of arming the pulse generator. In practice, the safety margin should be much bigger, as it's affected by the non-determinism of the operating system.
PG_TRIG [read-only]: Pulse generator triggered
read 1: pulse generator has been triggered and produced a pulse
read 0: pulse generator is busy or hasn't triggered yet
UPDATE [write-only]: Start Delay Update
write 1: Starts delay update procedure. The start and end times from [U/C/F][START/END] will be transferred in an atomic way to the internal delay/pulse generator registers
write 0: no effect.
UPD_DONE [read-only]: Delay Update Done
read 1: The delays from [U/C/F][START/END] have been loaded into internal registers
read 0: update operation in progress
FORCE_DLY [write-only]: Force Calibration Delay
write 1: preloads the delay line with the contents of FRR register. Used for self-calibration purposes.
write 0: no effect
NO_FINE [read/write]: Disable Fine Part update
write 1: disables updating of the fine part of the pulse delay to allow for producing faster signals (i.e. pulse width/spacing < 200 ns), at the cost of less accurate width/spacing control (multiple of 4 ms).
write 0: normal operation. Pulse width/spacing must be at least 200 ns.

3.2. Fine Range Register

HW prefix:	fd_channel_frr
HW address:	0x1
C prefix:	FRR
C offset:	0x4

Delay line tap setting at which the line generates an 8 ns (one cycle) longer delay than when set to 0.

31	30	29	28	27	26	25	24
-	-	-	-	-	-	-	-

23	22	21	20	19	18	17	16
-	-	-	-	-	-	-	-

15	14	13	12	11	10	9	8
-	-	-	-	-	-	FRR[9:8]

7	6	5	4	3	2	1	0
FRR[7:0]

FRR [read/write]: Fine Range

3.3. Pulse start time / offset (MSB TAI seconds)

HW prefix:	fd_channel_u_starth
HW address:	0x2
C prefix:	U_STARTH
C offset:	0x8

TAI seconds (8 upper bits) part of the pulse start absolute time (when in PG mode) / offset from trigger (when in delay mode).

31	30	29	28	27	26	25	24
-	-	-	-	-	-	-	-

23	22	21	20	19	18	17	16
-	-	-	-	-	-	-	-

15	14	13	12	11	10	9	8
-	-	-	-	-	-	-	-

7	6	5	4	3	2	1	0
U_STARTH[7:0]

U_STARTH [read/write]: TAI seconds (MSB)

3.4. Pulse start time / offset (LSB TAI seconds)

HW prefix:	fd_channel_u_startl
HW address:	0x3
C prefix:	U_STARTL
C offset:	0xc

TAI seconds (32 lower bits) part of the pulse start absolute time (when in PG mode) / offset from trigger (when in delay mode).

31	30	29	28	27	26	25	24
U_STARTL[31:24]

23	22	21	20	19	18	17	16
U_STARTL[23:16]

15	14	13	12	11	10	9	8
U_STARTL[15:8]

7	6	5	4	3	2	1	0
U_STARTL[7:0]

U_STARTL [read/write]: TAI seconds (LSB)

3.5. Pulse start time / offset (8 ns cycles)

HW prefix:	fd_channel_c_start
HW address:	0x4
C prefix:	C_START
C offset:	0x10

Sub-second part of the pulse start absolute time (when in PG mode) / offset from trigger (when in delay mode). Expressed as a number of 125 MHz clock cycles. Acceptable range: 0 to 124999999.

31	30	29	28	27	26	25	24
-	-	-	-	C_START[27:24]

23	22	21	20	19	18	17	16
C_START[23:16]

15	14	13	12	11	10	9	8
C_START[15:8]

7	6	5	4	3	2	1	0
C_START[7:0]

C_START [read/write]: Reference clock cycles

3.6. Pulse start time / offset (sub-cycle fine part)

HW prefix:	fd_channel_f_start
HW address:	0x5
C prefix:	F_START
C offset:	0x14

Sub-clock cycle part of the pulse start absolute time (when in PG mode) / offset from trigger (when in delay mode). Scales linearly to <0..8 ns>: 0 = 0 ps, 4095 = 7999 ps.

31	30	29	28	27	26	25	24
-	-	-	-	-	-	-	-

23	22	21	20	19	18	17	16
-	-	-	-	-	-	-	-

15	14	13	12	11	10	9	8
-	-	-	-	F_START[11:8]

7	6	5	4	3	2	1	0
F_START[7:0]

F_START [read/write]: Fractional part

3.7. Pulse end time / offset (MSB TAI seconds)

HW prefix:	fd_channel_u_endh
HW address:	0x6
C prefix:	U_ENDH
C offset:	0x18

TAI seconds (8 upper bits) part of the pulse end absolute time (when in PG mode) / offset from trigger (when in delay mode).

31	30	29	28	27	26	25	24
-	-	-	-	-	-	-	-

23	22	21	20	19	18	17	16
-	-	-	-	-	-	-	-

15	14	13	12	11	10	9	8
-	-	-	-	-	-	-	-

7	6	5	4	3	2	1	0
U_ENDH[7:0]

U_ENDH [read/write]: TAI seconds (MSB)

3.8. Pulse end time / offset (LSB TAI seconds)

HW prefix:	fd_channel_u_endl
HW address:	0x7
C prefix:	U_ENDL
C offset:	0x1c

TAI seconds (32 lower bits) part of the pulse end absolute time (when in PG mode) / offset from trigger (when in delay mode).

31	30	29	28	27	26	25	24
U_ENDL[31:24]

23	22	21	20	19	18	17	16
U_ENDL[23:16]

15	14	13	12	11	10	9	8
U_ENDL[15:8]

7	6	5	4	3	2	1	0
U_ENDL[7:0]

U_ENDL [read/write]: TAI seconds (LSB)

3.9. Pulse end time / offset (8 ns cycles)

HW prefix:	fd_channel_c_end
HW address:	0x8
C prefix:	C_END
C offset:	0x20

Sub-second part of the pulse endabsolute time (when in PG mode) / offset from trigger (when in delay mode). Expressed as a number of 125 MHz clock cycles. Acceptable range: 0 to 124999999.

31	30	29	28	27	26	25	24
-	-	-	-	C_END[27:24]

23	22	21	20	19	18	17	16
C_END[23:16]

15	14	13	12	11	10	9	8
C_END[15:8]

7	6	5	4	3	2	1	0
C_END[7:0]

C_END [read/write]: Reference clock cycles

3.10. Pulse end time / offset (sub-cycle fine part)

HW prefix:	fd_channel_f_end
HW address:	0x9
C prefix:	F_END
C offset:	0x24

Sub-clock cycle part of the pulse end absolute time (when in PG mode) / offset from trigger (when in delay mode). Scales linearly to <0..8 ns>: 0 = 0 ps, 4095 = 7999 ps.

31	30	29	28	27	26	25	24
-	-	-	-	-	-	-	-

23	22	21	20	19	18	17	16
-	-	-	-	-	-	-	-

15	14	13	12	11	10	9	8
-	-	-	-	F_END[11:8]

7	6	5	4	3	2	1	0
F_END[7:0]

F_END [read/write]: Fractional part

3.11. Pulse spacing (TAI seconds)

HW prefix:	fd_channel_u_delta
HW address:	0xa
C prefix:	U_DELTA
C offset:	0x28

TAI seconds between rising edges of subsequent output pulses.

31	30	29	28	27	26	25	24
-	-	-	-	-	-	-	-

23	22	21	20	19	18	17	16
-	-	-	-	-	-	-	-

15	14	13	12	11	10	9	8
-	-	-	-	-	-	-	-

7	6	5	4	3	2	1	0
-	-	-	-	U_DELTA[3:0]

U_DELTA [read/write]: TAI seconds

3.12. Pulse spacing (8 ns cycles)

HW prefix:	fd_channel_c_delta
HW address:	0xb
C prefix:	C_DELTA
C offset:	0x2c

Reference clock cycles between rising edges of subsequent output pulses.

31	30	29	28	27	26	25	24
-	-	-	-	C_DELTA[27:24]

23	22	21	20	19	18	17	16
C_DELTA[23:16]

15	14	13	12	11	10	9	8
C_DELTA[15:8]

7	6	5	4	3	2	1	0
C_DELTA[7:0]

C_DELTA [read/write]: Reference clock cycles

3.13. Pulse spacing (sub-cycle fine part)

HW prefix:	fd_channel_f_delta
HW address:	0xc
C prefix:	F_DELTA
C offset:	0x30

Sub-cycle part of spacing between rising edges of subsequent output pulses.

31	30	29	28	27	26	25	24
-	-	-	-	-	-	-	-

23	22	21	20	19	18	17	16
-	-	-	-	-	-	-	-

15	14	13	12	11	10	9	8
-	-	-	-	F_DELTA[11:8]

7	6	5	4	3	2	1	0
F_DELTA[7:0]

F_DELTA [read/write]: Fractional part

3.14. Repeat Count Register

HW prefix:	fd_channel_rcr
HW address:	0xd
C prefix:	RCR
C offset:	0x34

31	30	29	28	27	26	25	24
-	-	-	-	-	-	-	-

23	22	21	20	19	18	17	16
-	-	-	-	-	-	-	CONT

15	14	13	12	11	10	9	8
REP_CNT[15:8]

7	6	5	4	3	2	1	0
REP_CNT[7:0]

REP_CNT [read/write]: Repeat Count
CONT [read/write]: Continuous Waveform Mode
write 1: output will produce a contiguous square wave upon receptio of trigger pulse. The generation can be aborted by disabling the channel (DCRx.ENABLE = 0)
write 0: output will produce trains of REP_CNT+1 pulses.

fd_channel_wb_slave

Fine Delay Channel WB Slave

Contents: