Commit 91a51bea authored by Adam Wujek's avatar Adam Wujek 💬 Committed by Grzegorz Daniluk

docs/specifications/management: update wrs_failures with temperature info

DONE "Temperature inside the box too high"
Signed-off-by: Adam Wujek's avatarAdam Wujek <adam.wujek@cern.ch>
parent 1ffe30e1
...@@ -631,7 +631,7 @@ wrs-192.168.16.242# devmem 0xfffffd04 ...@@ -631,7 +631,7 @@ wrs-192.168.16.242# devmem 0xfffffd04
\item {\bf Temperature inside the box too high} \item {\bf Temperature inside the box too high}
\label{fail:other:temp} \label{fail:other:temp}
\begin{packed_enum} \begin{packed_enum}
\item [] \underline{Status}: TODO \emph{(depends on HDL)} \item [] \underline{Status}: DONE
\item [] \underline{Severity}: WARNING \item [] \underline{Severity}: WARNING
\item [] \underline{Description}:\\ \item [] \underline{Description}:\\
If the temperature raises too high we might break our electronics inside If the temperature raises too high we might break our electronics inside
...@@ -645,15 +645,22 @@ wrs-192.168.16.242# devmem 0xfffffd04 ...@@ -645,15 +645,22 @@ wrs-192.168.16.242# devmem 0xfffffd04
\item \emph{IC18} - temperature near the VCXO and PLLs (AD9516, \item \emph{IC18} - temperature near the VCXO and PLLs (AD9516,
CDCM6100) CDCM6100)
\end{itemize} \end{itemize}
\item [] \underline{SNMP objects}: \emph{(not yet implemented)}\\ \item [] \underline{SNMP objects}:\\
\texttt{WR-SWITCH-MIB::tempFPGA}\\ \texttt{WR-SWITCH-MIB::tempFPGA}\\
\texttt{WR-SWITCH-MIB::tempScbPsu.1}\\ \texttt{WR-SWITCH-MIB::tempPSL}\\
\texttt{WR-SWITCH-MIB::tempScbPsu.2}\\ \texttt{WR-SWITCH-MIB::tempPSR}\\
\texttt{WR-SWITCH-MIB::tempPLL} \texttt{WR-SWITCH-MIB::tempPLL}\\
\item [] \underline{Note}: we should report temperature from these 4 \texttt{WR-SWITCH-MIB::tempTholdFPGA}\\
sensors and set the threshold for each of them to raise an alarm. \texttt{WR-SWITCH-MIB::tempTholdPLL}\\
Temperature is read by the HAL to drive PWM inside the FPGA. HAL should \texttt{WR-SWITCH-MIB::tempTholdPSL}\\
report temperature to its area in the shared memory. \texttt{WR-SWITCH-MIB::tempTholdPSR}\\
\texttt{WR-SWITCH-MIB::tempWarning}\\
\item [] \underline{Note}:
\texttt{tempWarning} is raised when temperature read from any of these sensors
exceeds individually set threshold in \emph{.config}. When at least one threshold
temperature is not set tempWarning returns \emph{Threshold-not-set}.
Temperature is read by the HAL to drive PWM inside the FPGA. HAL reports
temperature to its area in the shared memory.
\end{packed_enum} \end{packed_enum}
\item {\bf Not supported SFP plugged into the cage (especially non 1-Gb SFP)} \item {\bf Not supported SFP plugged into the cage (especially non 1-Gb SFP)}
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment