/* ----------------------------------------------------------------------------
 *         ATMEL Microcontroller Software Support 
 * ----------------------------------------------------------------------------
 * Copyright (c) 2008, Atmel Corporation
 *
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * - Redistributions of source code must retain the above copyright notice,
 * this list of conditions and the disclaimer below.
 *
 * Atmel's name may not be used to endorse or promote products derived from
 * this software without specific prior written permission.
 *
 * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
 * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * ----------------------------------------------------------------------------
 */

/*
    Title: Memories implementation
*/

//------------------------------------------------------------------------------
//         Headers
//------------------------------------------------------------------------------

#include <board.h>
#include <pio/pio.h>
#include "board_memories.h"

/*
    Macros:
        READ - Reads a register value. Useful to add trace information to read
               accesses.
        WRITE - Writes data in a register. Useful to add trace information to
                write accesses.
*/
#define READ(peripheral, register)          (peripheral->register)
#define WRITE(peripheral, register, value)  (peripheral->register = value)


//------------------------------------------------------------------------------
//         Internal functions
//------------------------------------------------------------------------------

//------------------------------------------------------------------------------
//         Exported functions
//------------------------------------------------------------------------------
//------------------------------------------------------------------------------
/// Changes the mapping of the chip so that the remap area mirrors the
///   internal ROM or the EBI CS0.
//------------------------------------------------------------------------------
void BOARD_RemapRom()
{
    WRITE(AT91C_BASE_MATRIX, MATRIX_MRCR, 0);
}

//------------------------------------------------------------------------------
/// Changes the mapping of the chip so that the remap area mirrors the
///   internal RAM.
//------------------------------------------------------------------------------
void BOARD_RemapRam()
{
    WRITE(AT91C_BASE_MATRIX,
          MATRIX_MRCR,
          (AT91C_MATRIX_RCA926I | AT91C_MATRIX_RCA926D));
}



void BOARD_ConfigureVddMemSel(unsigned char VddMemSel)
{

    if (VddMemSel == VDDMEMSEL_3V3) {
            AT91C_BASE_MATRIX->MATRIX_EBICSA |= (1 << 16);
                    AT91C_BASE_MATRIX->MATRIX_EBICSA &= ~(1 << 17);
                        }
                            else {
                                    AT91C_BASE_MATRIX->MATRIX_EBICSA &= ~(1 << 16);
                                            AT91C_BASE_MATRIX->MATRIX_EBICSA &= ~(1 << 17);
                                                }
                                                }
                                                
//------------------------------------------------------------------------------
/// Configure DDR
//------------------------------------------------------------------------------
void BOARD_ConfigureDdram(unsigned char ddrModel, unsigned char busWidth)
{    
    AT91PS_HDDRSDRC2 pDdrc = AT91C_BASE_DDR2C;
    volatile unsigned int *pDdr = (unsigned int *) AT91C_DDR2;
    int i;
    volatile unsigned int cr = 0;
    unsigned short ddrc_dbw = 0;

    switch (busWidth) {
        case 16:
        default:
            ddrc_dbw = AT91C_DDRC2_DBW_16_BITS;
            break;

        case 32:
            ddrc_dbw = AT91C_DDRC2_DBW_32_BITS;
            break;

    }

    // Enable DDR2 clock x2 in PMC
    WRITE(AT91C_BASE_PMC, PMC_SCER, AT91C_PMC_DDR);

    // Disable anticipated read
    WRITE(pDdrc, HDDRSDRC2_HS, (READ(pDdrc, HDDRSDRC2_HS) | AT91C_DDRC2_NO_ANT));

    switch (ddrModel) {

        case DDR_MICRON_MT47H64M8: 
            // Step 1: Program the memory device type
            WRITE(pDdrc, HDDRSDRC2_MDR, ddrc_dbw   |
                                        AT91C_DDRC2_MD_DDR2_SDRAM);     // DDR2
            
            // Step 2:                            
            // 1. Program the features of DDR2-SDRAM device into the Configuration Register.                    
            // 2. Program the features of DDR2-SDRAM device into the Timing Register HDDRSDRC2_T0PR.            
            // 3. Program the features of DDR2-SDRAM device into the Timing Register HDDRSDRC2_T1PR.            
            // 4. Program the features of DDR2-SDRAM device into the Timing Register HDDRSDRC2_T2PR.            

            WRITE(pDdrc, HDDRSDRC2_CR, AT91C_DDRC2_NC_DDR10_SDR9  |     // 10 column bits (1K)
                                       AT91C_DDRC2_NR_14          |     // 14 row bits    (8K)
                                       AT91C_DDRC2_CAS_3          |     // CAS Latency 3
                                       AT91C_DDRC2_DLL_RESET_DISABLED
                                       ); // DLL not reset

            // assume timings for 7.5ns min clock period
            WRITE(pDdrc, HDDRSDRC2_T0PR, AT91C_DDRC2_TRAS_6       |     //  6 * 7.5 = 45 ns
                                         AT91C_DDRC2_TRCD_2       |     //  2 * 7.5 = 15 ns
                                         AT91C_DDRC2_TWR_2        |     //  2 * 7.5 = 15 ns
                                         AT91C_DDRC2_TRC_8        |     //  8 * 7.5 = 60 ns
                                         AT91C_DDRC2_TRP_2        |     //  2 * 7.5 = 15 ns
                                         AT91C_DDRC2_TRRD_1       |     //  1 * 7.5 = 7.5 ns
                                         AT91C_DDRC2_TWTR_1       |     //  1 clock cycle
                                         AT91C_DDRC2_TMRD_2);           //  2 clock cycles

            WRITE(pDdrc, HDDRSDRC2_T1PR, AT91C_DDRC2_TXP_2  |           //  2 * 7.5 = 15 ns
                                         200 << 16          |           // 200 clock cycles, TXSRD: Exit self refresh delay to Read command
                                         16 << 8            |           // 16 * 7.5 = 120 ns TXSNR: Exit self refresh delay to non read command
                                         AT91C_DDRC2_TRFC_14 << 0);     // 14 * 7.5 = 105 ns (must be 105 ns for 512M DDR)

            WRITE(pDdrc, HDDRSDRC2_T2PR, AT91C_DDRC2_TRTP_1   |         //  1 * 7.5 = 7.5 ns
                                         AT91C_DDRC2_TRPA_0   |         
                                         AT91C_DDRC2_TXARDS_7 |         //  7 clock cycles
                                         AT91C_DDRC2_TXARD_2);          //  2 clock cycles

            // Step 3: An NOP command is issued to the DDR2-SDRAM to enable clock.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_NOP_CMD);
            *pDdr = 0;
 
            // Initialization Step 3 (must wait 200 us) (6 core cycles per iteration, core is at 396MHz: min 13200 loops)
            for (i = 0; i < 13300; i++) {
                asm("    nop");
            }
            // Step 4:  An NOP command is issued to the DDR2-SDRAM 
            // NOP command -> allow to enable cke
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_NOP_CMD);
            *pDdr = 0;
            
            // wait 400 ns min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }

            // Step 5: An all banks precharge command is issued to the DDR2-SDRAM.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_PRCGALL_CMD);
            *pDdr = 0;
            
            // wait 400 ns min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }

            // Step 6: An Extended Mode Register set (EMRS2) cycle is  issued to chose between commercialor high  temperature operations.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_EXT_LMR_CMD);
            *((unsigned int *)((unsigned char *)pDdr + 0x4000000)) = 0;
         
            // wait 2 cycles min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }
            
            // Step 7: An Extended Mode Register set (EMRS3) cycle is issued to set all registers to 0.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_EXT_LMR_CMD);
            *((unsigned int *)((unsigned char *)pDdr + 0x6000000)) = 0;

            // wait 2 cycles min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }
             
            // Step 8:  An Extended Mode Register set (EMRS1) cycle is issued to enable DLL.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_EXT_LMR_CMD);
            *((unsigned int *)((unsigned char *)pDdr + 0x2000000)) = 0;

            // wait 200 cycles min
            for (i = 0; i < 10000; i++) {
                asm("    nop");
            }
            
            // Step 9:  Program DLL field into the Configuration Register.
            cr = READ(pDdrc, HDDRSDRC2_CR);
            WRITE(pDdrc, HDDRSDRC2_CR, cr | AT91C_DDRC2_DLL_RESET_ENABLED);
            
            // Step 10: A Mode Register set (MRS) cycle is issued to reset DLL.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_LMR_CMD);
            *(pDdr) = 0;

            // wait 2 cycles min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }
            
            // Step 11: An all banks precharge command is issued to the DDR2-SDRAM.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_PRCGALL_CMD);
            *(pDdr) = 0;

            // wait 400 ns min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }

            // Step 12: Two auto-refresh (CBR) cycles are provided. Program the auto refresh command (CBR) into the Mode Register.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_RFSH_CMD);
            *(pDdr) = 0;

            // wait 10 cycles min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }
            // Set 2nd CBR
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_RFSH_CMD);
            *(pDdr) = 0;

            // wait 10 cycles min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }
            
            // Step 13: Program DLL field into the Configuration Register to low(Disable DLL reset).
            cr = READ(pDdrc, HDDRSDRC2_CR);
            WRITE(pDdrc, HDDRSDRC2_CR, cr & (~AT91C_DDRC2_DLL_RESET_ENABLED));
            
            // Step 14: A Mode Register set (MRS) cycle is issued to program the parameters of the DDR2-SDRAM devices.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_LMR_CMD);
            *(pDdr) = 0;
    
            // Step 15: Program OCD field into the Configuration Register to high (OCD calibration default).
            cr = READ(pDdrc, HDDRSDRC2_CR);
            WRITE(pDdrc, HDDRSDRC2_CR, cr | AT91C_DDRC2_OCD_DEFAULT);
            
            // Step 16: An Extended Mode Register set (EMRS1) cycle is issued to OCD default value.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_EXT_LMR_CMD);
            *((unsigned int *)((unsigned char *)pDdr + 0x2000000)) = 0;

            // wait 2 cycles min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }
            
            // Step 17: Program OCD field into the Configuration Register to low (OCD calibration mode exit).
            cr = READ(pDdrc, HDDRSDRC2_CR);
            WRITE(pDdrc, HDDRSDRC2_CR, cr & (~AT91C_DDRC2_OCD_EXIT));
         
           // Step 18: An Extended Mode Register set (EMRS1) cycle is issued to enable OCD exit.
           WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_EXT_LMR_CMD);
            *((unsigned int *)((unsigned char *)pDdr + 0x6000000)) = 0;

            // wait 2 cycles min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }
            
            // Step 19,20: A mode Normal command is provided. Program the Normal mode into Mode Register.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_NORMAL_CMD);
            *(pDdr) = 0;

            // Step 21: Write the refresh rate into the count field in the Refresh Timer register. The DDR2-SDRAM device requires a
            // refresh every 15.625 ¦Ěs or 7.81 ¦Ěs. With a 100MHz frequency, the refresh timer count register must to be set with
            // (15.625 /100 MHz) = 1562 i.e. 0x061A or (7.81 /100MHz) = 781 i.e. 0x030d.
      
            // Set Refresh timer
            WRITE(pDdrc, HDDRSDRC2_RTR, 0x00000411);

            // Read optimization" shall be un-selected on this revision.
            WRITE(pDdrc, HDDRSDRC2_HS, 0x4);

            // OK now we are ready to work on the DDRSDR

            // wait for end of calibration
            for (i = 0; i < 500; i++) {
                asm("    nop");
            }

            break;


        case DDR_SAMSUNG_M470T6554EZ3_CE6:

             // Step 1: Program the memory device type
            WRITE(pDdrc, HDDRSDRC2_MDR, ddrc_dbw   |
                                        AT91C_DDRC2_MD_DDR2_SDRAM);     // DDR2
            
            // Step 2:                            
            // 1. Program the features of DDR2-SDRAM device into the Configuration Register.                    
            // 2. Program the features of DDR2-SDRAM device into the Timing Register HDDRSDRC2_T0PR.            
            // 3. Program the features of DDR2-SDRAM device into the Timing Register HDDRSDRC2_T1PR.            
            // 4. Program the features of DDR2-SDRAM device into the Timing Register HDDRSDRC2_T2PR.            
            WRITE(pDdrc, HDDRSDRC2_CR, AT91C_DDRC2_NC_DDR10_SDR9  |     // 10 column bits (1K)
                                       AT91C_DDRC2_NR_13          |     // 13 row bits    (8K)
                                       AT91C_DDRC2_CAS_3          |     // CAS Latency 3
                                       AT91C_DDRC2_DLL_RESET_DISABLED); // DLL not reset
          
          // assume timings for 7.5ns min clock period
            WRITE(pDdrc, HDDRSDRC2_T0PR, AT91C_DDRC2_TRAS_6       |     //  6 * 7.5 = 45   ns
                                         AT91C_DDRC2_TRCD_2       |     //  2 * 7.5 = 15 ns
                                         AT91C_DDRC2_TWR_2        |     //  2 * 7.5 = 15   ns
                                         AT91C_DDRC2_TRC_8       |      //  8 * 7.5 = 60   ns
                                         AT91C_DDRC2_TRP_2        |     //  2 * 7.5 = 15 ns
                                         AT91C_DDRC2_TRRD_2       |     //  1 * 7.5 = 7.5   ns
                                         AT91C_DDRC2_TWTR_1       |     //  1 clock cycle
                                         AT91C_DDRC2_TMRD_2);           //  2 clock cycles
          
          
            WRITE(pDdrc, HDDRSDRC2_T1PR, AT91C_DDRC2_TXP_2  |           //  2 * 7.5 = 15 ns
                                         200 << 16          |           // 200 clock cycles, TXSRD: Exit self refresh delay to Read command
                                         16 << 8            |           // 16 * 7.5 = 120 ns TXSNR: Exit self refresh delay to non read command
                                         AT91C_DDRC2_TRFC_14 << 0);     // 14 * 7.5 = 105 ns (must be 105 ns for 512M DDR)
          
          
            WRITE(pDdrc, HDDRSDRC2_T2PR, AT91C_DDRC2_TRTP_1   |         //  1 * 7.5 = 7.5 ns
                                         AT91C_DDRC2_TRPA_0   |         
                                         AT91C_DDRC2_TXARDS_7 |         //  7 clock cycles
                                         AT91C_DDRC2_TXARD_2);          //  2 clock cycles

            // Step 3: An NOP command is issued to the DDR2-SDRAM to enable clock.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_NOP_CMD);
            *pDdr = 0;
 
            // Initialization Step 3 (must wait 200 us) (6 core cycles per iteration, core is at 396MHz: min 13200 loops)
            for (i = 0; i < 13300; i++) {
                asm("    nop");
            }
            // Step 4:  An NOP command is issued to the DDR2-SDRAM 
            // NOP command -> allow to enable cke
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_NOP_CMD);
            *pDdr = 0;
            
            // wait 400 ns min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }

            // Step 5: An all banks precharge command is issued to the DDR2-SDRAM.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_PRCGALL_CMD);
            *pDdr = 0;
            
            // wait 400 ns min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }

            // Step 6: An Extended Mode Register set (EMRS2) cycle is  issued to chose between commercialor high  temperature operations.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_EXT_LMR_CMD);
            *((unsigned int *)((unsigned char *)pDdr + 0x2000000)) = 0; // BA[1] is set to 1 and BA[0] are set to 0.
         
            // wait 2 cycles min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }
            
            // Step 7: An Extended Mode Register set (EMRS3) cycle is issued to set all registers to 0.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_EXT_LMR_CMD);
            *((unsigned int *)((unsigned char *)pDdr + 0x3000000)) = 0; //BA[1] is set to 1 and BA[0] are set to 1.

            // wait 2 cycles min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }
             
            // Step 8:  An Extended Mode Register set (EMRS1) cycle is issued to enable DLL.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_EXT_LMR_CMD);
            *((unsigned int *)((unsigned char *)pDdr)) = 0; //BA[1] and BA[0] are set to 0.

            // wait 200 cycles min
            for (i = 0; i < 10000; i++) {
                asm("    nop");
            }
            
            // Step 9:  Program DLL field into the Configuration Register.
            cr = READ(pDdrc, HDDRSDRC2_CR);
            WRITE(pDdrc, HDDRSDRC2_CR, cr | AT91C_DDRC2_DLL_RESET_ENABLED);
            
            // Step 10: A Mode Register set (MRS) cycle is issued to reset DLL.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_LMR_CMD);
            *(pDdr) = 0;

            // wait 2 cycles min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }
            
            // Step 11: An all banks precharge command is issued to the DDR2-SDRAM.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_PRCGALL_CMD);
            *(pDdr) = 0;

            // wait 400 ns min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }

            // Step 12: Two auto-refresh (CBR) cycles are provided. Program the auto refresh command (CBR) into the Mode Register.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_RFSH_CMD);
            *(pDdr) = 0;

            // wait 10 cycles min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }
            // Set 2nd CBR
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_RFSH_CMD);
            *(pDdr) = 0;

            // wait 10 cycles min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }
            
            // Step 13: Program DLL field into the Configuration Register to low(Disable DLL reset).
            cr = READ(pDdrc, HDDRSDRC2_CR);
            WRITE(pDdrc, HDDRSDRC2_CR, cr & (~AT91C_DDRC2_DLL_RESET_ENABLED));
            
            // Step 14: A Mode Register set (MRS) cycle is issued to program the parameters of the DDR2-SDRAM devices.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_LMR_CMD);
            *(pDdr) = 0; //BA[1:0] are set to 0.
    
            // Step 15: Program OCD field into the Configuration Register to high (OCD calibration default).
            cr = READ(pDdrc, HDDRSDRC2_CR);
            WRITE(pDdrc, HDDRSDRC2_CR, cr | AT91C_DDRC2_OCD_DEFAULT);
            
            // Step 16: An Extended Mode Register set (EMRS1) cycle is issued to OCD default value.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_EXT_LMR_CMD);
            *((unsigned int *)((unsigned char *)pDdr + 0x1000000)) = 0; //BA[1] is set to 0 and BA[0] is set to 1

            // wait 2 cycles min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }
            
            // Step 17: Program OCD field into the Configuration Register to low (OCD calibration mode exit).
            cr = READ(pDdrc, HDDRSDRC2_CR);
            WRITE(pDdrc, HDDRSDRC2_CR, cr & (~AT91C_DDRC2_OCD_EXIT));
         
            // Step 18: An Extended Mode Register set (EMRS1) cycle is issued to enable OCD exit.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_EXT_LMR_CMD);
            *((unsigned int *)((unsigned char *)pDdr + 0x3000000)) = 0; //BA[1] is set to 1and BA[0] is set to 1.

            // wait 2 cycles min
            for (i = 0; i < 100; i++) {
                asm("    nop");
            }
            
            // Step 19,20: A mode Normal command is provided. Program the Normal mode into Mode Register.
            WRITE(pDdrc, HDDRSDRC2_MR, AT91C_DDRC2_MODE_NORMAL_CMD);
            *(pDdr) = 0;

            // Step 21: Write the refresh rate into the count field in the Refresh Timer register. The DDR2-SDRAM device requires a
            // refresh every 15.625 s or 7.81 s. With a 100MHz frequency, the refresh timer count register must to be set with
            // (15.625 /100 MHz) = 1562 i.e. 0x061A or (7.81 /100MHz) = 781 i.e. 0x030d.
      
            // Set Refresh timer
            WRITE(pDdrc, HDDRSDRC2_RTR, 0x00000411);

            // OK now we are ready to work on the DDRSDR

            // wait for end of calibration
            for (i = 0; i < 500; i++) {
                asm("    nop");
            }

            break;


        default:
            break;
    }
}



//------------------------------------------------------------------------------
/// Initialize and configure the SDRAM
//------------------------------------------------------------------------------
void BOARD_ConfigureSdram(unsigned char busWidth)
{

    // TO BE IMPLEMENTED IN CASE SDRAM IS MOUNTED.

}

//------------------------------------------------------------------------------
/// Configures the EBI for NandFlash access. Pins must be configured after or
/// before calling this function.
//------------------------------------------------------------------------------
void BOARD_ConfigureNandFlash(unsigned char busWidth)
{
}

//------------------------------------------------------------------------------
/// Configures the EBI for NandFlash access at 48MHz. Pins must be configured
/// after or before calling this function.
//------------------------------------------------------------------------------
void BOARD_ConfigureNandFlash48MHz(unsigned char busWidth)
{
}

//------------------------------------------------------------------------------
/// Configures the EBI for NorFlash access
/// \Param busWidth Bus width 
//------------------------------------------------------------------------------
void BOARD_ConfigureNorFlash(unsigned char busWidth)
{
}

//------------------------------------------------------------------------------
/// Configures the EBI for NorFlash access at 48MHz.
/// \Param busWidth Bus width 
//------------------------------------------------------------------------------
void BOARD_ConfigureNorFlash48MHz(unsigned char busWidth)
{
}
