Check md5sums of files in the wrs-firmware.tar with stored in file
checksums.md5. When checksum does not match abort the update.
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Try to source in the subshell downloaded dot-config.
This test can detect problems like unterminated quoted string:
/bin/sh: /tmp/dot-config: line 59: syntax error: unterminated quoted string
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

In some rare cases it can happen that locally stored dot-config is not valid.
For example, when firmware on the switch was updated, but the old dot-config is
still used. However, such scenario is unlikely because new firmware should
contain new dot-config.

--check whether sourcing was successful
--Replace "." with "source" when sourcing dot-config.
--Redirect errors to the stderr.
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Perform uplift of the buildroot to the 2016.02.
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

When switch's firmware with buildroot older than 2016.02 was updated via
copying wrs-firmware.tar with buildroot at least 2016.02 to the
/update partition, then hwinfo in the flash was overwriten.
Such behaviour was caused by crashing during execution of /wr/bin/sdb-read.
Crashing sdb-read caused the following if's condition from the file
/etc/init.d/hwinfo to be false.

if /wr/bin/sdb-read /dev/mtd5ro > /dev/null; then

This triggered later overwrite of hwinfo partition.

/wr/bin/sdb-read was crashing because during update the binary /wr/bin/sdb-read
was called from just extracted firmware. Problem pops up when libraries
required by sdb-read are in the different versions in the old and the new
firmware. Unfortunatelly, this problem cannot be easily solved, since we cannot
change the update procedure in already installed firmware (the one that is
performing update).

Implemented solution does the following:
--change the name of /wr/etc/sdb-for-dataflash to /wr/etc/sdb-for-dataflash.bin
  by this /etc/init.d/hwinfo script exits with an error without modification
  to the hwinfo partition.
--rename link /etc/rcS/S90hwinfo to /etc/rcS/S10hwinfo, which will trigger
  update of hwinfo partition earlier during the boot.
--restart switch after update of hwinfo in the flash
--remove calls of /etc/init.d/hwinfo during the update
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

The problem is that the "reboot" command sends the signal to the init. However,
it looks like init queues all incoming signals. They're handled after all
"sysinit" commands from the inittab are finished.
reboot -f skip sending the signal and triggers the reboot immediately.

This problem pop up after update of a buildroot to version 2016.02.
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

When Barebox's menu is displayed, it erases all messages from the screen.
Put some extra newlines to move out printed messages from the screen.
These messages could be seen now in the terminal's history.
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

move lighttpd configuration from /var/www/lighttpd.config to
/etc/lighttpd/lighttpd.conf.
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Don't install lighttpd configs for WRS, we have our own.
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

We don't want to enable IPv6 support in the busybox, since we don't support
IPv6 on the switch.

Add patch taken from the buildroots repo:
7a5be2a0 busybox: tweak IPv6/largefile handling
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

We don't use ifplugd since Feb 2014. See the commit:
162fb24e userspace: run dhcpc in background forever, not through auto means
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

There is no need to create cpio, tar and bzip2 images, since we don't use them
anyway. We assemble images on our own in build/scripts/wrs_build_wraprootfs.
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Change done due to uplift of the buildroot to the 2016.02
Please note that some of the options just changed their position.

Some changes:

remove:
--DOS2UNIX
--UNIX2DOS
--FDFORMAT (we don't have floppy)
--EJECT (we don't have CD/DVD)
--HDPARM (we don't have ATA drives)
--ETHER_WAKE (to send wake-on-lan magic packet)
--DNSD (we don't need DNS server)
--NAMEIF (we don't want to change names of interfaces)

remove the following, since they're provided by prosps_ng:
--pidof
--top
--uptime
--free
--kill*
--ps
--sysctl
--watch

add:
--LFS (large file support)
--MD5_SMALL=0 (We don't care so much about the size, more about
  the performance. Use the fastest. Difference in the size is very
  small anyway.)
--SHA3_SMALL=0 (like above)
--CONFIG_GZIP_FAST=2 (like above, use the fastest)
--FEATURE_LESS_WINCH and FEATURE_LESS_ASK_TERMINAL allow to display i.e.
  "less" command via serial terminal with non standard terminal sizes.
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

In case there are errors it will print process name instead of pid.
for example:
/wr/bin/wrs_checkcfg: Error: Configuration "XXX" not found
instead of:
<pid-123>: Error: Configuration "PORT00_PARAMS" not found
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Buildroot forces procps-ng to install binaries in the /bin insted of /usr/bin.
As a side effect libprocps.pc was installed at /lib/pkgconfig instead of
/usr/lib/pkgconfig. Which directory is not included into final image.

Added patch taken from buildroot's repo:
0e07a5ede package/procps-ng: install libprocps.pc in staging/usr/lib/pkgconfig/
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Fix the warning (for perl < 5.21.x) whihch becomes an error
(for perl >= 5.21.x):

defined(@array) is deprecated at kernel/timeconst.pl line 373.
  (Maybe you should just omit the defined()?)

This error pops up on newer systems. It is not related with the change of
the buildroot, but with the host version of perl.
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Instead of keeping the list of archives in build/download-info which should be
downloaded for buildroot, we use "make source" to do the same job.
However, the task of building buildroot had to split into 3 tasks:
--init (unpack and configure buildroot)
--download (download the source of used buildroot packages)
--build (compile buildroot packages, etc.)

The reason for this change is to avoid updating the download-info file when
buildroot package is updated. Additionally ltrace is not downloaded as an
archive, but it is cloned git repo. After the clone it is packed into archive.
In the current state our framework cannot do the same.
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Remove binaries/usr/lib/libbfd-2.21.1.so and /usr/bin/nm from the repo.
Instead use the compiled versions in buildroot.

Patch the installation rule to install only "nm", when
PACKAGE_BINUTILS_TARGET is not used(!).
libbfd-2.21.1.so is installed by default by the installation rule of
PACKAGE_BINUTILS.

Binary nm was added in the commit:
d2a486cc rootfs_override: add /usr/bin/nm and its libbfd
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

There is a conflict in struct scm_timestamping
between wrs-socket.c and linux kernel code from the buildroot (4.4).

update PPSI due to similar issue
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

--Remove file THIS_IS_NOT_YOUR_ROOT_FILESYSTEM. We wrap rootfs ourself, we know
  what we're doing.
--remove symlink /etc/dropbear, before creating such directory
  Creating the symlink was added in the buildroot's commit:
  e7d04dd2 package/dropbear: fix generating keys on RO file systems
--overwrite symlink for var/run->../tmp
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

make 3.82 splits the work differently. When using buildroot with
the make > 3.81 buildroot uses BR2_JLEVEL= (preferably 0 for automatic number
of jobs setting).
For make =< 3.81 BR2_JLEVEL= is ignored and build is done using only one job.
Passing -j allows to build with many jobs, but many warning messages are
printed:
make[2]: warning: -jN forced in submake: disabling jobserver mode.

Use BR_JLEVEL=0, this allows buildroot to pick automatically number of jobs.
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

get rid of warning:
WARNING: "wr_nic_pstats_callback" [/home/awujek/wrs/wr-switch-sw/kernel/wr_pstats/wr_pstats.ko] undefined!
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Change the names of interfaces from wr0..wr17 (wrX) to wri1..wri18 (wriX).
Such change was done to avoid confusion that ports on the front panel are
numbered from 1 to 18, while in software they were numbered from 0 to 17.
Inconsistency started to show up especially in messages produced by software
causing confusion.

Be aware that even after these changes some software internally uses indexing
or ports from 0 to 17.
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

README file was outdated. Additionally, part of this information is included
in the wrs-user-manual.
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

from wrX to wriX+1
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

libwr may produce some verbose messages.
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>