EDMS versions
The list below shows the EDMS versions, together with links to the pages. The currently supported version for any card is always the last one.
Front module: EDA-02541
Version | Description |
---|---|
EDA-02541-V1-0 | Closed First version |
EDA-02541-V2-0 | Closed Second version, adds selectable I/O terminations and PCB adjustments for changes in front panel design, together with the front panel design itself |
EDA-02541-V3-0 | Closed Third version, adds silkscreen for general-purpose switches and implements small corrections in schematics |
EDA-02541-V4-0 | ClosedAdds hardwired PCB version number, adds inverting buffers on LEDs, replaces FP right angled LEDs and other minor corrections in silkscreen |
EDA-02541-V4-1 | Latest version. Change of value of pull-up resistors. See Hardware review 27-09-2017. 320 produced in 2018. Another 230 in 2023. |
Rear transition module (Motherboard + piggyback) : EDA-02452
Board requires a piggyback (Eg: EDA-03712)
Version | Description |
---|---|
EDA-02452-V1-1 | Closed First version. Uses RTM piggyback EDA-02494 |
EDA-02452-V2-1 | Closed Second version, removes ground planes on top and bottom sides of the cards deemed dangerous for EMC reasons |
EDA-02452-V3-1 | LEMO 2-pin version No longer supported V3 moves the 100-pin connector to the inside of the board, to avoid bending the panel |
EDA-02452-V3-3 | Closed First version with D-Sub9 piggyback. Layout of connectors on piggyback incorrect. See issue #1751 |
EDA-02452-V3-4 | Closed Uses same RTM motherboard but with new piggy back EDA-03712-V2-0 for DB9 connector compatibility. Incomplete EDMS. |
EDA-02452-V3-5 | D-sub9 version. Uses same RTM motherboard but with new piggy back EDA-03712-V2-1 for DB9 connector compatibility. |
Rear transition module piggyback in LEMO 0S: EDA-02494: No longer supported
Mounted on EDA-02452, to give EDA-02452-V3-1.
Version | Description |
---|---|
EDA-02494-V1-0 | Closed First version |
EDA-02494-V2-0 | No longer supported Second version, connects the RTMP detection lines to the 100-pin connector and the N lines on the Lemo 0S connector |
Rear transition module piggyback in D-Sub9: EDA-03712
Mounted on EDA-02452, to give EDA-02452-V3-3
Version | Description |
---|---|
EDA-03712-V1-0 | Closed First version of a 2-channel 1 i/p, 5 o/p RTM piggyback with D-Sub9 connectors |
EDA-03712-V2-0 | Corrects issue #1751 found on version 1. Uses different connectors with built-in screwlocks |
Rear transition module in optical: EDA-03760
Standalone board, plugs directly at the back of CONV-TTL-RS485
Version | Description |
---|---|
EDA-03760-V1-0 | First version of a 3-channel 1 i/p, 2 o/p RTM in optical with ST connectors |
INFO FROM 9 January 2020
-
Front module EDA-02541-V4-1
-
RTMs The front module can be fitted with one of these Rear Transition Modules RTMs
-
CONV-TTL-RTM-RS485-DB9 (RS485 I/O with D-sub9 connectors): EDA-02452-V3-5.
This RTM is composed of:- EDA-02452-V3-0 (motherboard)
- EDA-03712-V2-1 (D-sub9 daughterboard)
-
CONV-RS485-OPT-RTM (Optical I/O with ST connectors): EDA-03760-V1-1.
-
CONV-TTL-RS485-RTM (RS485 I/O with Lemo-2 pin connectors): EDA-02452-V3-1 (No longer supported).
This RTM is composed of:- EDA-02452-V3-0 (motherboard)
- EDA-02494-V2-0 (LEMO 2-pin daughterboard)
-
Theodor-Adrian Stana, Denia Bouhired, Eva Gousiou, Erik van der Bij - 4 March 2022