Which SFP transceiver and fibre type to use for White Rabbit
Standard compatible to 1000BASE-BX10
As in White Rabbit it is of uttermost importance to have equal cable lenghts in both directions, a single fibre should be used for sending data both directions.
As we claim a compatibility with Ethernet, we stick to what the Gigabit Ethernet standards propose:
http://en.wikipedia.org/wikis/Gigabit_Ethernet
"1000BASE-BX10 is a capable of up to 10 km over a single strand of
single-mode fiber, with a different wavelength going in each
direction.
The terminals on each side of the fibre are not equal, as the one
transmitting "downstream" (from the center of the network to the
outside) uses the 1490 nm wavelength, and the one transmitting
"upstream" uses the 1310 nm wavelength."
I believe that with 'terminals' they mean terminal at a high level, not
the connectors. The norm is
http://standards.ieee.org/getieee802/download/802.3-2008_section5.pdf
(section 59), but it's not clear from the specification what connectors
(LC or SC) they're proposing for the two sides.
Searching for "1000BASE-BX10 connector" comes up with LC connectors (mostly for Cisco).
Conclusion: White Rabbit should follow the 1000BASE-BX10 standard and
use 1310/1490 pairs with a single LC connector.
More specifically, the Switch ports transmitting downstream (to
endpoints) should use 1490nm on the transmitter and 1310nm on the
receiver.
Parameter | Downstream side (usually Switch) | Upstream side (ususally End node) |
Ethernet type | IEEE 802.3ah 1000BASE-BX10-D | IEEE 802.3ah 1000BASE-BX10-U |
Tx wavelength | 1490 nm | 1310 nm |
Rx wavelength | 1310 nm | 1490 nm |
Compliant SFP types
Brand | Switch side | Node side |
Axcen Photonics | AXGE-3454-0531 | AXGE-1254-0531 |
To be completed and verified!
Optoway
Optoway SFPs: SPB-7610BLG, SPB-7710, 7810, 7910 (Tom)
Axcen
AXCEN SFPs: AXGE-3454-0531 and AXGE-1254-0531 (Tom)
Zyxel
ZyXEL SFP-BX1310-10, Mini Gbic, 1.25Gbit, IEEE 802.3ah
ZyXEL SFP-BX1490-10, Mini Gbic, 1.25Gbit, IEEE 802.3ah
Apac
LS38-C3S-TC-N-B9 Transceiver SFP APAC Opto 1.25 Gbps, TX1310/RX1490, FP,
3.3V, TX: -3 -9 dBm, RX: -21dBm, TTL, 10km
LS48-C3S-TC-N-B4 Transceiver SFP APAC Opto 1.25 Gbps, TX1490/RX1310, FP,
3.3V, TX: -3 -9 dBm, RX: -21dBm, TTL, 10km
TP-Link
TP-Link TL-SM321A/B
http://www.tp-link.com/en/products/details/?model=TL-SM321A
Fibre G652 type
Use G652 fibre. This fibre is optimised for 1310nm, which compensates for the dispersion wavelength of the worst of the two wavelengths used.
-
White Rabbit should follow the 1000BASE-BX10 standard and use 1310/1490 pairs with a single LC connector
-
Measuring propagation delay over a 1.25 Gbps bidirectional data
link - Appendix
A
- note: images for 1550 instead of 1490, results will be similar.
- The cable type is important that kind of has to be the best at the wavelength of the worst laser.
Achim Vollhardt, Erik van der Bij - 27 January 2012