- 09 Apr, 2020 2 commits
-
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
This reverts commit 9c8412e3. S59leap_seconds_file_update is already there to call the script at boot time.
-
- 08 Apr, 2020 6 commits
-
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
Fixes ifconfig down issue for LPDC ports.
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
Load values from tx_phase_cal.conf file only if MD5 matches. Otherwise, generate new values.
-
Grzegorz Daniluk authored
-
- 02 Apr, 2020 2 commits
-
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
-
- 31 Mar, 2020 4 commits
-
-
Maciej Lipinski authored
-
Maciej Lipinski authored
-
Maciej Lipinski authored
So far, only LDPC tx calibration was indicated by blinking link led, now the same behavior was added when LPDC rx calibration is ongoing.
-
Maciej Lipinski authored
Make sure that the status LED does go green before the LPDC tx calibration is finished.
-
- 30 Mar, 2020 2 commits
-
-
Maciej Lipinski authored
Setting the options to force dot-config/IP over DHCP can be dangerous. Until now, the switch would wait endlessly in an infinite loop. This commit introduces a way to escape the loop. This can be done by connecting to the back UART and pressing any key.
-
Grzegorz Daniluk authored
-
- 27 Mar, 2020 3 commits
-
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
Now it represents the overall status of system clock: - verification with NTP time - leap seconds file
-
Jean-Claude BAU authored
-
- 26 Mar, 2020 2 commits
-
-
Grzegorz Daniluk authored
-
Grzegorz Daniluk authored
-
- 25 Mar, 2020 2 commits
-
-
Jean-Claude BAU authored
snmp: For WR extension, wrsPtpRTT is set with rawDelayMM wr_mon: For WR extension, the value of delayMM displayed correspond to rawDelayMM
-
Jean-Claude BAU authored
This field is set now to NA if the local leap second file is used
-
- 23 Mar, 2020 1 commit
-
-
Grzegorz Daniluk authored
-
- 20 Mar, 2020 1 commit
-
-
Grzegorz Daniluk authored
Since driver reads periodically MDIO registers (timer function to check link state) and HAL reads periodically LPDC MDIO registers (through ioctl call) it happened once in a while that ioctl read operation would be interleaved with timer function. As a result HAL would get the value read from a different MDIO register than the one requested. This had caused occasional link restarts on LPDC ports.
-
- 13 Mar, 2020 2 commits
-
-
Jean-Claude BAU authored
-
Jean-Claude BAU authored
-
- 11 Mar, 2020 1 commit
-
-
Jean-Claude BAU authored
-
- 10 Mar, 2020 2 commits
-
-
Jean-Claude BAU authored
-
Jean-Claude BAU authored
The script files have been moved in host_tools directory.
-
- 09 Mar, 2020 1 commit
-
-
Jean-Claude BAU authored
- New script to generate the VLAN kconfig - Allows raw configuration for vlan ports - New key for PTP VID
-
- 06 Mar, 2020 3 commits
-
-
Jean-Claude BAU authored
-
Jean-Claude BAU authored
-
Jean-Claude BAU authored
-
- 05 Mar, 2020 6 commits
-
-
Jean-Claude BAU authored
-
Jean-Claude BAU authored
-
Jean-Claude BAU authored
-
Jean-Claude BAU authored
-
Jean-Claude BAU authored
-
Jean-Claude BAU authored
-