Commit 188dee7b authored by Grzegorz Daniluk's avatar Grzegorz Daniluk

doc: sections reorganized

parent 1e11a971
...@@ -378,6 +378,7 @@ The resulting binary \textit{wrc.bin} can be then used with the loader from ...@@ -378,6 +378,7 @@ The resulting binary \textit{wrc.bin} can be then used with the loader from
the White Rabbit PTP Core (see section \ref{Programming FPGA} for details). the White Rabbit PTP Core (see section \ref{Programming FPGA} for details).
% ########################################################################## % ##########################################################################
\newpage
\section{Programming FPGA with WRPC firmware} \section{Programming FPGA with WRPC firmware}
\label{Programming FPGA} \label{Programming FPGA}
...@@ -493,6 +494,7 @@ CERN network) for more instructions. If you are outside CERN and would like to ...@@ -493,6 +494,7 @@ CERN network) for more instructions. If you are outside CERN and would like to
use one of these boards, please contact us. use one of these boards, please contact us.
% ========================================================================== % ==========================================================================
\newpage
\section{Using WRPC shell} \section{Using WRPC shell}
\subsection{Writing configuration} \subsection{Writing configuration}
...@@ -706,7 +708,9 @@ Depending on your board, 1-PPS output is produced on: ...@@ -706,7 +708,9 @@ Depending on your board, 1-PPS output is produced on:
\end{itemize*} \end{itemize*}
% ========================================================================== % ==========================================================================
\subsection{Diagnostics via SNMP} \newpage
\section{WRPC diagnostics}
\subsection{SNMP}
\label{Diagnostics via SNMP} \label{Diagnostics via SNMP}
Up to the version 4.0 of WRPC the only way to perform diagnostics Up to the version 4.0 of WRPC the only way to perform diagnostics
...@@ -1224,7 +1228,8 @@ whenever they are activated. This happens at initialization time and ...@@ -1224,7 +1228,8 @@ whenever they are activated. This happens at initialization time and
whenever you change the MAC address or \textit{vlan} choice. whenever you change the MAC address or \textit{vlan} choice.
% ========================================================================== % ==========================================================================
\subsection{Network Services} \newpage
\section{Network Services}
\label{Network Services} \label{Network Services}
If built with \texttt{CONFIG\_IP=y}, \textit{wrpc-sw} implements the following If built with \texttt{CONFIG\_IP=y}, \textit{wrpc-sw} implements the following
...@@ -1258,7 +1263,8 @@ udp-based network services, in addition to \textit{ptp}: ...@@ -1258,7 +1263,8 @@ udp-based network services, in addition to \textit{ptp}:
\end{longtable} \end{longtable}
% ========================================================================== % ==========================================================================
\subsection{VLAN Support} \newpage
\section{VLAN Support}
\label{VLAN Support} \label{VLAN Support}
The White Rabbit node can be configured to be vlan-aware, by setting The White Rabbit node can be configured to be vlan-aware, by setting
...@@ -1302,6 +1308,7 @@ processing and get back to the ``standard'' packet-filter rules. ...@@ -1302,6 +1308,7 @@ processing and get back to the ``standard'' packet-filter rules.
\end{longtable} \end{longtable}
% ########################################################################## % ##########################################################################
\newpage
\section{Troubleshooting} \section{Troubleshooting}
\label{Troubleshooting} \label{Troubleshooting}
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment