The logic used to control WR switch leds is removed from HAL and
imported into PPSi. It prevents HAL from reading PPSi shared memory.

Modification made to be more coherent as delayCoefficient is in range [-1,1] instead of [-2,2].

This is a temporary implementation that will be reviewed when the PPSi
live configuration will be implemented.

add monitor variable to struct hal_port_state
Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Signed-off-by: Adam Wujek <adam.wujek@cern.ch>

Will be reintroduced later with HA profile.

- Code optimization for size
- HA is not compiled ( only PTP & WR )
- ...

See commit 'Simplify WRS calibration functions' below

- Has Hal is no longer used for ingress/egress latencies, we must then
take them from the configuration file
- Definition used by the common servo (WR & HA)
- Implementation of the IDLE state
See previous commit 'Review of WR protocol implementation'

See commit 'Simplify WRS calibration functions' below

It has been improvement to make it works with WR extension but the final
mechanism has to be improved to make it more simple.

As WR extension share now the same servo than L1Sync extension, the only
service required from HAL is the value of the bit-slide. Then a
simplification can be done by removing some functions and some obsolete
function parameters

This tool is used to follow the value of a monotonic clock to check if
it does not does big jumps. This jumps may affect the precision of the
timeout in PPSi. They can occur when the nanosecond adjustement is done
in the servo (WR & HA profiles).

In WR extension, the egress and ingress latencies are already included
in the exchanged deltas (TX/RX). This modification allows for an
extension to remove the egress/ingress latencies from the calculation of
the RX and TX timestamps. This feature is used in the WR extension.

Force to stay in UNCALIBRATED state if externalPortConfigurationEnabled
is set to true and desiredState to UNCALIBRATED.

- When the number of bit used for the calculation was smaller than 16,
the result of the calculation was 0.

- Take into account the rounding in time conversion
- New implementation of pp_time_hardwarize

- Add extra parameters in unpack_announce and run_ext_state_machine
callbacks

- Removed master_msg, s1, execute slave

- It has now its own state table
- The servo is shared with L1Sync extension. It means that servo
calculation is now following the new standard IEEE 1588
- It stay compatible with older versions of the switch. The correction
field value in the exchange messages are still not compliant with the
standard to keep the compatibility.

- For WR extension, we keep the old way to stay compliant with previous
version of WR
- The changes are applied to HA extension and compliant now with the
IEEE standard (delayAsymmetry sent in the CField of [P]DelayReq msg,
...)

After reviewing the code with Maciej, this time-out does not seem to be
used in a very coherent way. We decided then to remove it.

- Make externalPortConfiguration compliant with the PTP specifications
- Optimize code for externalPortConfiguration
- Optimize code for slaveOnly
- Replace "CONFIG_HAS_P2P && ppi->delayMechanism==P2P" by an inline
function

. Better integrate of code optimization with PPSi Kconfig
. PPSi Kconfig changes to simplify the code in PPSi and avoid #ifdef ..
. Improve code optimization
. Move some declaration in ppsi.h in other files to ligthen ppsi.h
. Improvement of timers: global or instance dependent, dyn. allocation,
renaming for better diagnostics, disabling allowed, ...
. New behaviour for the PPS output generation (configurable,...)
. Move control of the timing mode from HAL to PPSi
. Optimization of code when a Protocol extension is not available
. BMCA: Calculate the ebest,... only one time and then trigger all
instances to execute the bmca state descision
. Fix bug in the calculation of the clockIdentity to bring it into
compliance with PTP spec 2008 document
. Fix a bug related to Announce message received in SLAVE/UNCALIB
. WR ext: use dynamic timer and adapt to new PPS generation
. HA ext: Fix bug in fault injection mechanism

Risk of overflow in some cases.

offsetFromMaster and meanDelay are updated in currentDS only when a PPSi
instance is SLAVE.

- New L1Sync and PTP servo calculation (delayAsym,...)
- Make function calls more uniforms between extensions
- refactoring
- Add a new state machine to enable/disable an extension and provide
only PTP support: New timer, new hooks, ...
- Fix bug in time format conversion
- Code removed when an extension is not required (#ifdef XXX )
- Align the PTP and L1Sync servo calculation (shared fct, same
calculation,...)
- Force only one servo running at a given time for a given instance
- New servo reset hook : called by main loop
- Add function to converte a time into a string
- Force to stay in FAULTY state during 60s
- Optimise function wrs_enable_timing_output()